Emissions: catalytic converter, oxygen sensors, EVAP · Petrol vehicles

P0496 EVAP: flow detected during a non-purge condition

Standard definition: Evaporative Emission System High Purge Flow

SeverityMedium
Is it safe to drive?Drivable
Estimated cost£10 – £290
Can you check it yourself?Yes, the first steps

What does P0496 mean?

The engine is drawing vapour from the canister when the canister valve should be closed. Hard starting after refuelling is the typical symptom. Instead of releasing petrol vapour from the tank into the air, the EVAP system collects it in a charcoal canister and burns it in the engine.

Drivable: You can keep driving, but don't ignore it; have it checked at the first opportunity.

⚠️ Not closing the fuel cap properly after refuelling is the most common cause of this code; close it and the code may clear by itself after a few days of driving.

P0496 symptoms

P0496 causes (most to least common)

  1. Most common Purge valve stuck open (most common)
  2. Valve dirty / sticking

How do you check and fix P0496?

  1. Check the fuel cap first: tighten it until it clicks and inspect its seal.
  2. Visually check the canister and its hoses.
  3. For a definite diagnosis, have a smoke (EVAP) test done.

P0496 repair cost

Depending on the cause, roughly £10 – £290 (parts + labour; an approximate range that varies by garage and region). Jobs such as cleaning a connector or a simple adjustment may cost less than the lower end; replacing a major part comes close to the upper end. Getting the diagnosis right first avoids replacing parts unnecessarily.

Related fault codes

Frequently asked questions

What does fault code P0496 mean?

P0496 means "Evaporative Emission System High Purge Flow": EVAP: flow detected during a non-purge condition. The engine is drawing vapour from the canister when the canister valve should be closed. Hard starting after refuelling is the typical symptom. Instead of releasing petrol vapour from the tank into the air, the EVAP system collects it in a charcoal canister and burns it in the engine.

Can you drive with P0496?

Drivable. You can keep driving, but don't ignore it; have it checked at the first opportunity. Not closing the fuel cap properly after refuelling is the most common cause of this code; close it and the code may clear by itself after a few days of driving.

What causes a P0496 fault?

Most common causes: purge valve stuck open (most common), valve dirty / sticking. For a definitive diagnosis, live data and any other stored codes should be assessed together with this code.

How much does a P0496 repair cost?

Depending on the cause, it costs roughly £10 – £290 (parts + labour; an approximate range that varies by garage and region). It may be fixed by simply cleaning a connector or may need a part replaced; the correct diagnosis comes first.

Will clearing the P0496 code fix the problem?

No. Clearing the code only switches the light off temporarily; if the fault isn't fixed, the code comes back within a few drives. Recently cleared codes can also be spotted from the OBD readiness monitors — an important check when buying used.

Emissions: catalytic converter, oxygen sensors, EVAP codes

P0030Oxygen sensor heater control circuit fault (bank 1 sensor 1, upstream of the catalytic converter (front))P0031Oxygen sensor heater control circuit low (bank 1 sensor 1, upstream of the catalytic converter (front))P0032Oxygen sensor heater control circuit high (bank 1 sensor 1, upstream of the catalytic converter (front))P0036Oxygen sensor heater control circuit fault (bank 1 sensor 2, downstream of the catalytic converter (rear))P0037Oxygen sensor heater control circuit low (bank 1 sensor 2, downstream of the catalytic converter (rear))P0038Oxygen sensor heater control circuit high (bank 1 sensor 2, downstream of the catalytic converter (rear))P0050Oxygen sensor heater control circuit fault (bank 2 sensor 1, upstream of the catalytic converter (front))P0051Oxygen sensor heater control circuit low (bank 2 sensor 1, upstream of the catalytic converter (front))P0052Oxygen sensor heater control circuit high (bank 2 sensor 1, upstream of the catalytic converter (front))P0056Oxygen sensor heater control circuit fault (bank 2 sensor 2, downstream of the catalytic converter (rear))P0057Oxygen sensor heater control circuit low (bank 2 sensor 2, downstream of the catalytic converter (rear))P0058Oxygen sensor heater control circuit high (bank 2 sensor 2, downstream of the catalytic converter (rear))P0130Oxygen sensor circuit fault (bank 1 sensor 1, upstream of the catalytic converter (front))P0131Oxygen sensor signal low (bank 1 sensor 1, upstream of the catalytic converter (front))P0132Oxygen sensor signal high (bank 1 sensor 1, upstream of the catalytic converter (front))P0133Oxygen sensor slow response (bank 1 sensor 1, upstream of the catalytic converter (front))P0134No activity from the oxygen sensor (bank 1 sensor 1, upstream of the catalytic converter (front))P0135Oxygen sensor heater circuit fault (bank 1 sensor 1, upstream of the catalytic converter (front))

All emissions: catalytic converter, oxygen sensors, evap codes → · All OBD fault codes →

This page is for general information; details may vary by make and engine. For a definitive diagnosis, see an authorised service centre or a specialist mechanic.