Ignition and misfire · Petrol and diesel

P0300 Random / multiple cylinder misfire

Standard definition: Random/Multiple Cylinder Misfire Detected

SeverityHigh
Is it safe to drive?With care, short distances
Estimated cost£50 – £590
Can you check it yourself?Mechanic needed

What does P0300 mean?

From momentary drops in crankshaft speed, the ECU detected that more than one cylinder is firing unevenly (misfiring). A misfire that can't be pinned to one cylinder usually points to a common cause: fuel pressure, an air leak, the ignition system or bad fuel.

With care, short distances: Don't set off on a long journey; take it to a garage as soon as possible. Stop if the symptoms get worse.

⚠️ If the light is flashing, unburnt fuel is going into the catalytic converter; driving like this for long can melt it.

P0300 symptoms

P0300 causes (most to least common)

  1. Most common Worn spark plugs or plug leads
  2. Air leak at the intake manifold (vacuum hose, gasket)
  3. Low fuel pressure (pump, filter, regulator)
  4. Dirty / faulty injectors
  5. Poor-quality or contaminated (watery) fuel
  6. Valve clearance, loss of compression (in advanced cases)

How do you check and fix P0300?

  1. First check in live data which cylinders' misfire counters are rising.
  2. Remove the spark plugs; check electrode wear, oil fouling and soot, and replace them if they are past their change interval.
  3. With the engine running, listen for hissing on the intake side; check the vacuum hoses.
  4. Look at the fuel trim values: a long-term trim above +10% points to an air leak or low fuel.
  5. If the problem continues, have the fuel pressure and compression tested.

❌ Common mistake: Replacing coils and injectors all in one go. With a random misfire, the common causes (air leak, fuel pressure, spark plugs) should be ruled out first.

P0300 repair cost

Depending on the cause, roughly £50 – £590 (parts + labour; an approximate range that varies by garage and region). Jobs such as cleaning a connector or a simple adjustment may cost less than the lower end; replacing a major part comes close to the upper end. Getting the diagnosis right first avoids replacing parts unnecessarily.

Related fault codes

Frequently asked questions

What does fault code P0300 mean?

P0300 means "Random/Multiple Cylinder Misfire Detected": Random / multiple cylinder misfire. From momentary drops in crankshaft speed, the ECU detected that more than one cylinder is firing unevenly (misfiring). A misfire that can't be pinned to one cylinder usually points to a common cause: fuel pressure, an air leak, the ignition system or bad fuel.

Can you drive with P0300?

With care, short distances. Don't set off on a long journey; take it to a garage as soon as possible. Stop if the symptoms get worse. If the light is flashing, unburnt fuel is going into the catalytic converter; driving like this for long can melt it.

What causes a P0300 fault?

Most common causes: worn spark plugs or plug leads, air leak at the intake manifold (vacuum hose, gasket), low fuel pressure (pump, filter, regulator). For a definitive diagnosis, live data and any other stored codes should be assessed together with this code.

How much does a P0300 repair cost?

Depending on the cause, it costs roughly £50 – £590 (parts + labour; an approximate range that varies by garage and region). It may be fixed by simply cleaning a connector or may need a part replaced; the correct diagnosis comes first.

Will clearing the P0300 code fix the problem?

No. Clearing the code only switches the light off temporarily; if the fault isn't fixed, the code comes back within a few drives. Recently cleared codes can also be spotted from the OBD readiness monitors — an important check when buying used.

Ignition and misfire codes

All ignition and misfire codes → · All OBD fault codes →

This page is for general information; details may vary by make and engine. For a definitive diagnosis, see an authorised service centre or a specialist mechanic.